Turcite® Machined Parts         Call Toll Free 800-888-2605  Plastic Machining  Acetal Machined Parts  CPVC Machined Parts  Delrin Machined Parts  ETFE Machined Parts  ECTFE Machined Part  FEP Machined Part  Fluorosint Machined Parts  Halar Machined Part  Kel-F Machined Part  Kynar Machined Part  Macor Ceramic  Neoflon Machined Parts  Nylatron Machined Parts  Nylon Machined Parts  Nylon 6 Machined Parts  PCTFE Machined Parts  Peek Machined Parts  Polyamide-Imide Parts  Polyimide Parts  Polyurethane Molded Part  PPS Machined Part  PTFE Machined Parts  PVC Machined Parts  Rulon Machined Part  Ryton PPS Parts  Semitron Parts  Techtron Machined Parts  Teflon Machined Parts  Tefzel Machined Parts  Torlon Parts  Turcite Parts  UHMW Machined Parts  Ultem Parts  Vespel Machined Parts  Home  E-Mail  Map  Terms TURCITE® MACHINED PARTS M&P can make Turcite Machined Parts to your specifications. MATERIAL DESCRIPTION Turcite® is a self-lubricating thermoplastic bearing material manufactured by American Variseal Bearings (formerly Shamban Polymer Technologies) Group. These materials are cost effective, chemically resistant, wear resistant, and can be used in a wide range of temperatures. There are two grades of Turcite®; Turcite® A and Turcite® X. Both grades of Turcite® are acetal-based materials and their properties and applications can be compared to Delrin AF®.  Turcite® materials are available in rod form only. NOTABLE MATERIAL • Self-lubricating • Low cost • High chemical resistance • Moisture resistant • Always oven annealed for stress-relief GRADES OF TURCITE Turcite® A (also known as Turcite ® TA) • Turcite® A is suitable for moderate to heavy loads at moderate speeds. • Turcite® A performs well under vibratory and dynamic loading and is readily machinable. • Turcite® A has higher wear resistance than Turcite® X. • Turcite® A has a maximum continuous service temperature of 180°F (80°C). • Turcite® A is BLUE in color. Turcite® X (also known as Turcite® TX) • Turcite® X excels in low load and high speed applications. • Turcite® X can be easily machined, and has lower friction than Turcite® A. • Turcite® X has minimal hygroscopic characteristics and possesses low thermal expansion properties, resulting in a structurally stable material. • Turcite® X has a maximum continuous service temperature of 180°F (80°C). • Turcite® X is RED in color. CUSTOM MACHINED PARTS Processing and machining of Turcite parts take place in a completely controlled environment. We maintain a complete record of our products. M&P's state of the art facilities are always open for you to visit. For a quote on your custom Turcite parts click on the e-mail or give us a call at 1-800-888-2605 Some Turcite® parts we machined are: Balls Nozzels Semiconductor Parts Back Up Rings Pads Sheaves Blocks Parts Spacers Bushings Plugs Supports Cams Rings Valve Seats Caps Rods Washers Guides Rollers Wear Pads Medical Parts Seals     TURCITE is a registered trademark of American Variseal Bearings  M&P Flange & Pipe Protection Inc.  9426 Katy Fwy  Bldg #11  Houston, TX 77055  Phone: 800-888-2605   Fax: 713-463-6343        sales@m-p.com   Copyright© 2010