M&P Flange & Pipe Protection Peek™ Machined Parts         Call Toll Free 800-888-2605




 Plastic Machining
 Acetal Machined Parts
 
CPVC Machined Parts
 
Delrin Machined Parts
 
ETFE Machined Parts
 
ECTFE Machined Part
 
FEP Machined Part
 
Fluorosint Machined Parts
 
Halar Machined Part
 
Kel-F Machined Part
 
Kynar Machined Part
 
Macor Ceramic
 
Neoflon Machined Parts
 
Nylatron Machined Parts
 
Nylon Machined Parts
 
Nylon 6 Machined Parts
 
PCTFE Machined Parts
 
Peek Machined Parts
 
Polyamide-Imide Parts
 
Polyimide Parts
 
Polyurethane Molded Part
 
PPS Machined Part
 
PTFE Machined Parts
 
PVC Machined Parts
 
Rulon Machined Part
 
Ryton PPS Parts
 
Semitron Parts
 
Techtron Machined Parts
 
Teflon Machined Parts
 
Tefzel Machined Parts
 
Torlon Parts
 
Turcite Parts
 
UHMW Machined Parts
 
Ultem Parts
 
Vespel Machined Parts

 Home
 E-Mail
 Map
 Terms

Peek Plastic Connector
     PEEK™ MACHINED PARTS
Peek Extruded Tubes

M&P can make custom Peek™ Machined Parts to your specifications.


MATERIAL DESCRIPTION

PEEK ™ is an abbreviation for polyetheretherketone, a high performance engineering thermoplastic. PEEK grades offer good chemical and water resistance, and can operate at high temperatures. PEEK can be used continuously to 480°F (250°C) and in hot water or steam without permanent loss in physical properties. For use in hostile environments, PEEK is a high strength alternative. PEEK carries a V-0 flammability rating and exhibits very low smoke and toxic gas emission when exposed to flame. Unfilled PEEK is approved by the FDA for food contact applications

NOTABLE MATERIAL FEATURESPeek Hex Socket Thread Plug
● Excellent chemical resistance
● Very low moisture absorption
● Inherently good wear and abrasion resistance
● Unaffected by continuous exposure to hot water or steam


GRADES OF PEEK

PEEK (Unfilled)
This general purpose grade is not reinforced and offers the highest elongation and toughness of all PEEK grades.
PEEK material is available in the following colors:
● Light brown (Natural color)
● Black
Black PEEK is ideal for instrument components where aesthetics are important, as well as for seal components where ductility and inertness are important.
Unfilled PEEK grades comply with FDA regulation 21 CFR 177.2415 for repeated food contact.


PEEK (30% Glass Filled)Peek Seat Rings
PEEK has an increase in flexural modules and a reduction in expansion rate with the addition of glass fibers. This grade is ideal for structural applications that require improved strength, stiffness, or stability, especially at temperatures above 300°F (150°C). Glass-filled PEEK is only available a light brown color.

PEEK (30% Carbon Filled)
PEEK has enhanced compressive strength and stiffness with the addition of carbon fibers, and a dramatically lower expansion rate. It offers designers optimum wear resistance and load carrying capability in a PEEK-based product. This grade provides 3½ times higher thermal conductivity than non reinforced PEEK -- dissipating heat from the bearing surface faster. Carbon-filled PEEK is black in color.

PEEK (Bearing Grade)
This grade of PEEK, containing carbon fiber reinforced with graphite and PTFE lubricants, offers the lowest coefficient of friction and the is the easiest grade of PEEK to machine parts from. Bearing grade PEEK has an excellent combination of low friction, low wear, high limiting PV, low mating part wear, and easy machining. Bearing grade PEEK is black or dark grey in color.

CUSTOM MACHINED PARTS
Processing and machining of PEEK parts take place in a completely controlled environment. We maintain a complete record of our products. We build excellence into every part we machine. M&P's state of the art facilities are always open for you to visit.
For a quote on your custom PEEK parts click on the e-mail or give us a call at
1-800-888-2605.

Some of the machined parts we do are:Plastic Machined Parts

Balls Nozzels Semiconductor Parts
Back Up Rings Pads Sheaves
Blocks Parts Spacers
Bushings Plugs Supports
Cams Rings Valve Seats
Caps Rods Washers
Guides Rollers Wear Pads
Medical Parts Seals  



Ketron®-Peek
PEEK- Virgin and Filled
PEEK- Glass-Filled
PEEK- Carbon-Filled
PEEK-HT™
Polyetheretherketone - PEEK
Tecapeek™

Let M&P machine and supply your Peek ™ material needs. We can provide:
Peek™ Rod
Peek™ Slab
Peek™ Tube
Peek™ Machining
Peek™ Film
Peek™ Glass-Filled
Peek™ Carbon-Filled
Peek™ Ketron
Peek™ Tecapeek™
PeekHT™

Call us today at 1-800-888-2605 or e-mail us at sales@m-p.com

™ Registered Trademark of Victrex For Peek, PeekHT
® Registered Trademark of Quadrant For Ketron
® Registered Trademark of Ensinger For Tecapeek


 M&P Flange & Pipe Protection Inc.
 9426 Katy Fwy Bldg #11
 Houston, TX 77055
 Phone: 800-888-2605 Fax: 713-463-6343               sales@m-p.com
Copyright© 2010                                                                                                     The American Expres CardVISAMasterCard